background image

SPECIFICATIONS

Model

KX300.2    KX400.2    KX500.2    KX800.2

RMS Power

In Watts, All Channels Driven

@ 13.8, 4

Ω 

Stereo, 0.085% THD    75 x 2

100 x 2         125 x 2

200 x 2

@ 13.8V, 2

Ω 

Stereo, 0.2% THD      150 x 2        200 x 2         250 x 2        400 x 2

@ 13.8V, 4

Ω 

Mono, 0.4% THD       300              400              500              800

Dynamic Power 

In Watts, All Channels Driven

@ 14.4V, 4

Ω 

Stereo                      110 x 2        150 x 2         205 x 2        295 x 2

@ 14.4V, 2

Ω 

Stereo                      175 x 2        217 x 2         285 x 2        420 x 2

@ 14.4V, 4

Ω 

Mono                       350              435              570              840

Length With Shroud                     16”              19.25”          22.5”           25.75”

(40.64cm)    (48.90cm)     (57.15cm)    (65.41cm)

Specifications common to all models

Height:

2.5 inches / 6.35 centimeters

Width:

10.125 inches / 25.7 centimeters

Length W

Without SShroud: Subtract 5” (12.7cm) from chart above

Frequency R

Response:

20 Hz - 20 KHz, + 0 /- 1 dB

Input SSensitivity:

170 mV - 5 V low level, 340 mV - 10 V high level

Signal-tto-N

Noise R

Ratio:

>95 dB, a-weighted, re: rated power

Electronic C

Crossover:

Variable high or low pass, 50 - 200 Hz, 12 dB/octave

KickBass B

Boost:

Variable 0 to +18 dB boost @ 40 Hz

10

Summary of Contents for KX300.2















Reviews: