background image

Extol

 Auditorium Seating

Assembly Instructions

Assemble units as described herein only. To do otherwise 
may result in instability. All screws, nuts and bolts must be  
tightened securely and must be checked periodically after  
assembly. Failure to assemble properly, or to secure parts 
may result in assembly failure and personal injury.

7

Seat Attachment 

Note:

 Seat size and location 

are noted on the space-planning 

layout. Each seat assembly is 

marked with its size. Stage seats 

at site location according to the 

space plan. 

1.  Starting at one end of a row and 

one seat at a time, position a 

seat assembly onto the two seat 

support brackets of the uprights. 

Align the mounting holes of the 

assembly with the holes of the 

brackets. Place a flat washer on 

a M8 x 25mm cap screw and 

loosely attach the seat assembly 

points to the seat support 

brackets. Do not tighten fully at 

this time (Figure 6).

2. When all seats of a row are loosely 

attached, tighten all M8 x 25mm 

bolts in the row securing seats to 

upright support brackets. Check 

for free seat rotation up and down 

and adjust if necessary. Install 

all seat-mount shrouds to seat 

support brackets by snapping into 

place (Figure 6).

3. At this time, tighten all hardware 

securing backs to uprights, and 

tighten all floor anchors, properly 

securing uprights to the floor 

according to proper anchor 

specifications.

Summary of Contents for Extol













Reviews: