Keysight U8001A User'S And Service Manual Download Page 3

Page: 3 / 81

Keysight U8001A/U8002A User’s and Service Guide

Safety Symbols

The following symbols on the instrument and in the documentation indicate

precautions that must be taken to maintain safe operation of the instrument.

Direct current

Off (supply)

Alternating current

On (supply)

Both direct and alternating current

Equipment protected throughout by

double insulation or reinforced

insulation.

Three-phase alternating current

Caution, risk of electric shock.

Earth (ground) terminal

Caution, risk of danger (refer to this

manual for specific Warning or Caution

information.

Protective conductor terminal

Caution, hot surface.

Frame or chassis terminal

Out position of a bi-stable push

control.

Equipotentiality

In position of a bi-stable push control.

Summary of Contents for U8001A


















































































Search results

Summary of Contents for U8001A

Reviews:

Related manuals for U8001A

Brands by name

Popular brands

Keysight U8001A, User'S And Service Manual

Search results

Summary of Contents for U8001A

Reviews:

Related manuals for U8001A

Brands by name

Popular brands