Keysight U1401B User'S And Service Manual Download Page 37

Page: 37 / 159

Getting Started

Keysight U1401B User’s and Service Guide

Display selection with the Hz key

The frequency measurement function is able to detect the presence of harmonic

currents in neutral conductors and determines, whether these neutral currents are
the result of unbalanced phases or non- linear loads. Press

to enter the

frequency measurement mode for current or voltage measurements. The voltage

or current values will be displayed on the secondary display and the frequency

values on the primary display. Press this key again to step through frequency (Hz),

duty cycle (%), or pulse width (ms). This allows simultaneous monitoring of

real-time voltage or current with frequency, duty cycle, or pulse width.

After you press and hold

for more than one second, the primary display will

revert to voltage or current measurement values.

Table 1-9

Measurement functions and corresponding display selection with the

Hz key

Measurement function

Primary display

Secondary display

AC voltage

Frequency (Hz)

AC voltage

Duty cycle (%)

Pulse width (ms)

DC voltage

Frequency (Hz)

DC voltage

Duty cycle (%)

Pulse width (ms)

AC+DC voltage

Frequency (Hz)

AC+DC voltage

Duty cycle (%)

Pulse width (ms)

AC current

Frequency (Hz)

AC current

Duty cycle (%)

Pulse width (ms)

DC current

Frequency (Hz)

DC current

Duty cycle (%)

Pulse width (ms)

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands