Keysight U1401B User'S And Service Manual Download Page 134

Page: 134 / 159

Maintenance

134

Keysight U1401B User’s and Service Guide

Figure 6-2

Recharging the batteries

Fuse replacement

Replace any blown fuse in the instrument according to the following procedures:

Power down the instrument and disconnect all the test leads. Make sure that

the charging adapter is also removed.

Remove the battery cover and the batteries.

Loosen the three screws found on the bottom of the case and remove the

bottom cover.

Take out the circuit board as shown in

Figure 6-3

Gently remove the defective fuse by prying one end of the fuse loose and

sliding it out of the fuse bracket.

Replace it with a new fuse of the same size and rating. Make sure the new fuse

is centered in the fuse holder.

External AC

adapter jack

Charging indication
Green: Fully charged
Yellow: Charging

Set slide switch

at the CHARGE

position

NOTE

This manual provides only the fuse replacement procedures, but not the fuse

replacement markings.

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands