Keysight U1401B User'S And Service Manual Download Page 130

Page: 130 / 159

Maintenance

130

Keysight U1401B User’s and Service Guide

Maintenance

General maintenance

Besides the hazards mentioned above, dirt or moisture in the terminals can also

distort the readings. The cleaning procedure is outlined below:

Turn the instrument off and remove the test leads.

Turn the instrument over and shake out any dirt that may have accumulated in

the terminals.

Wipe the case with a damp cloth and mild detergent — do not use abrasives or

solvents containing benzine, benzene, toluene, xylene, acetone or similar

chemicals. Also, do not spray cleaner liquid directly onto the instrument,

because it may seep into the case and cause damage. Wipe the contacts in

each terminal with a clean swab moistened in alcohol.

Make sure the instrument has dried completely before using it.

CAUTION

Repairs or services which are not covered in this manual should only be

performed by qualified personnel.

WARNING

Make sure that the terminal connections are correct for a particular
measurement before making any measurement. To avoid damaging the
instrument, do not exceed the rated input limit.

WARNING

To avoid electrical shock or damage to the instrument, prevent water from
getting inside the case.

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands