Keysight N9923A User Manual Download Page 35

Page: 35 / 276

Keysight N9923-90001 User’s Guide 35

Preparing for Initial Use of Your New FieldFox
Connector Care

Connector Care

— Never store connectors, airlines, or calibration standards loose in a box. This

is a common cause of connector damage.

— Install protective end caps when connectors are not in use.

— Keep connector temperature the same as the test instrument. Holding the

connector in your hand or cleaning connector with compressed air can
significantly change the temperature. Wait for connector temperature to

stabilize before using in calibration or measurements.

— Do not touch the mating plane surfaces. Natural skin oils and microscopic

particles of dirt are difficult to remove from these surfaces.

— Do not set connectors contact-end down on a hard surface. The plating and

mating plane surfaces can be damaged if the interface comes in contact
with any hard surface.

— Wear a grounded wrist strap and work on a grounded, conductive table

mat. This helps protect the analyzer and devices from electrostatic
discharge (ESD).

— Refer to

“Connector Care” on page 35

Because of the very small and precise mechanical tolerances of mmWave

connectors, minor defects, damage, and dirt can significantly degrade

repeatability and accuracy. In addition, a dirty or damaged connector can

destroy connectors that are mated to it. For this reason, NEVER use a

damaged connector. See also

http://na.support.keysight.com/pna/connectorcare/Connector_Care.htm

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 35 / 276

Search results

Summary of Contents for N9923A

Reviews: