manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 155 / 276

Share
Download
Keysight N9923A User Manual Download Page 155

Keysight N9923-90001 User’s Guide                                                                                                                      155

Pulse Measurements Mode – Option 330
Pulse Measurement Settings

 

Marker Settings

Markers are not allowed with Meter-style measurements.

Markers are displayed on 

Tr 1

 and also on the zoom trace if the marker is 

within the zoom window time span.

Up to six standard markers can be used to provide readouts of the Y-axis 
amplitude at the current X-axis location. 

The six standard markers can also be used as Delta Markers. 

Learn more about standard markers in 

“All about Markers” on page 174

.

Amplitude Markers

Amplitude markers are horizontal dotted lines that you can move to any 
amplitude level on the screen. The two amplitude markers can be set 

independently or used as a pair of delta markers.

Amplitude markers can be used as a visual comparison aid with the pulse 

measurement traces.

How to make Amplitude Marker settings

— Press 

Marker

 

— Then 

More

 

— Then 

Ampl Markers

— Then choose from the following:

—

OFF

 Amplitude markers are NOT displayed.

—

ON

 Amplitude markers ARE displayed at their previous positions.

— Then 

Ampl Mkr 1 or 2

— Enter a value in dBm for the marker using the numeric keypad, the 

 

arrows, or the rotary knob.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments