manualshive.com logo in svg

Keysight N9340B, Demo Manual

Share
Download
Keysight N9340B Demo Manual Download Page 4

4

Caption

Function

1

External DC power connector

Provides input for the DC power source via an AC-DC adapter or automotive type DC adapter. 

2

LED indicator (charging)

Light is {On} when the battery is charging

3

LED indicator

Light is {On} when external DC power is connected to the tester

4

USB interface (device)

Connects the analyzer to a PC

5

USB interface (host)

Connects the analyzer to a USB memory stick or disk

6

Headphone

Connects the analyzer to a headphone

7

LAN interface

Connects the analyzer to a PC for SCPI remote control

8

RF OUT connector

The output for the built-in tracking generator. Enabled with Option TG3.

9

EXT TRIG IN/REF IN  
(BNC, female)

Connects to an external TTL signal or a 10 MHz refer ence signal. The TTL signal is used to  
trigger the analyzer’s internal sweep.

10

RF IN connector (50 Ω)

Accepts an external input with a frequency range from 100 kHz to 3 GHz, tunable to 9 kHz

Section 1

Top Panel Overview

10

9

8

7

1

2

3 4

5

6

Summary of Contents for N9340B


































Reviews:

No comments

Brands by name

Popular brands

Load more brands