manualshive.com logo in svg

Keysight N9020B, Installation Note, Page: 27 / 30

Share
Download
Keysight N9020B Installation Note Download Page 27

Installation Note N9020-90257

27

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Verify Hardware Installation

1.

Turn on the analyzer and wait for the instrument to fully boot up. 

2.

Verify the spectrum analyzer application loads and sweeps as expected. Press 

System

, 

Show 

Hard ware

 on the analyzer and verify that the Main board and the 

BBIQ Interface Board

 identify 

themselves as:

—

BBIQ

—

BBIQ Interface

Licensing the Option 

Installation Procedure over USB

1.

Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.

2.

Redeem the Option Upgrade Entitlement Certificate by following the instructions on the 

Certificate.

3.

After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an 

attached License File.

4.

Locate a USB storage device. Perform a virus scan on this device before use.

5.

Save the License File to the root directory of the USB storage device.

6.

Connect the USB storage device to one of the MXA USB ports. Windows will detect the new 

hardware and may display the configuration menu shown in 

Figure 19

. This menu may be 

configured according to your preferences.

Figure 19 

USB Storage Device Configuration Menu

Summary of Contents for N9020B































Reviews:

No comments