Keysight N5247-60106 Installation Note Download Page 47

Page: 47 / 54

Installation Note N5247-90106 47

Installation Procedure for the Upgrade

— W79 (reuse) (N5242-60012) A24 IF multiplexer board P3 to A16

SPAM board J1

— W81 (reuse) (N5242-60014) A24 IF multiplexer board P403 to A16

SPAM board J4

— W83 (reuse) (N5242-60016) A24 IF multiplexer board P803 to A16

SPAM board J6

Step 41. Reinstall the Testset Stabilizer Bracket on the A24 IF

Multiplexer Board

Reinstall the stabilizer bracket - see

Figure 2

Step 42. Reinstall the A23 Test Set Motherboard

1. For instructions on reinstalling the board, click the Chapter 7 bookmark

“Removing and Replacing the A23 test set motherboard” in the PDF
Service Guide

Step 43. Install Cables on the A23 Test Set Motherboard

If not already done in a previous step, install the following new ribbon cables

and wire harness in the order listed. To see an image showing their locations,

click the Chapter 6 bookmark “Bottom Ribbon Cables and Wire Harnesses,
4-Port, Option 419” in the PDF Service Guide

. New parts are listed in

Table 1

on page 8

— Ribbon cable (N5247-60015) from A28 mixer brick (2) J52 to A23 test set

motherboard J552

— Ribbon cable (N5247-60018), A61 port 3 70 GHz doubler J1 to A23 test set

motherboard J5

— Ribbon cable (N5247-60018), A62 port 4 70 GHz doubler J1 to A23 test set

motherboard J3

— Ribbon cable (N5247-60021), A43 port 3 bias tee to A23 test set

motherboard J543

— Ribbon cable (N5247-60021), A44 port 4 bias tee to A23 test set

motherboard J544

— Ribbon cable (N5247-60020), A47 port 3 receiver attenuator to A23 test set

motherboard J206

Follow instructions carefully when making cable connections, especially

wire harness connections. Incorrect connections can destroy components,

resulting in additional customer costs.

1. See

“Downloading the Online PNA Service Guide” on page 6

Summary of Contents for N5247-60106























































Search results

Summary of Contents for N5247-60106

Reviews:

Related manuals for N5247-60106

Brands by name

Popular brands

Keysight N5247-60106, Installation Note

Search results

Summary of Contents for N5247-60106

Reviews:

Related manuals for N5247-60106

Brands by name

Popular brands