manualshive.com logo in svg

Keysight N4431D, Reference Manual

Share
Download
Keysight N4431D Reference Manual Download Page 50

 2-12                                                                                Electronic Calibration Modules Reference Guide

Preparing ECal for Use
Operating and Safety Precautions

2-

Input Power Level

Operating Temperature

The temperature of the ECal module must be within the following temperature 

range to meet the operating specifications.

— N755xA Series: +15 °C to +35 °C and up to 75% relative humidity (RH).
— N469xD Series: +20 °C to +26 °C and up to 95% relative humidity (RH) at 

40 °C, non-condensing.

— N443xD Series: +20 °C to +26 °C and up to 95% relative humidity (RH) at 

40 °C, non-condensing.

For more details, see 

“Environmental Specifications” on page 5-2

.

Before performing a calibration, make sure the input power and DC levels 

do not exceed the values indicated in 

Table 2-10

.

Table 2-10 Input Power Limits 

Parameter

ECal Module Series

N755xA

N469xD

N4431/2/3D

Typical Maximum Input Power (linearity) 

a,

 

b

a. If the maximum input power is exceeded when calibrating, compression may occur.

b. When using the PNA-X, the power level can be increased after calibration with minimal 

impact on measurement accuracy.

–15.0 dBm –5.0 dBm

-7.0 dBm

Typical Maximum DC Level Applied to Test Port

c

c. Maximum DC level applied to test port, where Option 0DC for N469xD and N443xD is set to 0 

volts.

0 Volts

±

10 Volts

± 3 Volts

Typical Damage Level

 

+10.0 dBm +10.0 dBm +20.0 dBm

Summary of Contents for N4431D















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands