Keysight MIPI M-PHY User Manual Download Page 66

Page: 66 / 76

Keysight MIPI M-PHY Frame Generator User Guide

Using the Software

Wildcards

If a sequence name contains one or more wildcards, the name of the

sequence that is actually running changes as the wildcards are replaced

by particular values during the run time, depending on the test specifics.

Table 3

lists the names of the wildcards that are supported for sequence

names, along with their possible values. No wildcards are mandatory.

Table 3

Supported wildcards for sequence names and their possible values

Wildcard

Values

Tab in which the value of the wildcard can be
changed

[HsGear]

Gear1A, …, Gear5B

Data Rates Tab

[Mode]

Cont, Burst

Protocol Tab

[Amplitude]

Large, Small

Protocol Tab

[Channel]

Data0, DataAll

For Rx Test Mode (UniPro Script Generator):
Protocol Tab;
For Tx Test Mode (UniPro Script Generator):
Pattern Tab

Summary of Contents for MIPI M-PHY













































































Search results

Summary of Contents for MIPI M-PHY

Reviews:

Related manuals for MIPI M-PHY

Brands by name

Popular brands

Keysight MIPI M-PHY, User Manual

Search results

Summary of Contents for MIPI M-PHY

Reviews:

Related manuals for MIPI M-PHY

Brands by name

Popular brands