Keysight E8718A User Manual Download | Manualshive

Page: 30 / 53

background image

3

System Software and User Application

30

Keysight E8718A Radar Target Simulator User Guide

System Requirements

The following table lists the minimum system requirements for the E8718A

software.

Operation system

Windows ® 7 (32-bit and 64-bit) and above
Starter, Home Basic, Home Premium, Professional, Ultimate,

or Enterprise

Processor speed

1 GHz 32-bit (x86) or
1 GHz 64-bit (x64);
Itanium 64 is not supported

Available memory

1 GB minimum

Available hard-disk space

20 MB

«
...
28
29
30
31
32
...
»

Summary of Contents for E8718A






















































Reviews:

No comments

Related manuals for E8718A

Brand: Oakcastle Pages: 32

Brand: Galaxy Pages: 38

Brand: KREAFUNK Pages: 44

Brand: Radio Shack Pages: 1

Brand: Ranger Electronic Pages: 11

Brand: stabo Pages: 32

Brand: Sandstrom Pages: 76

TOUGH ENOUGH GS350DL

Brand: Grundig Pages: 21

Brand: Quintezz Pages: 12

Brand: Keiki Pages: 55

Brand: Furuno Pages: 99

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

SRF-M95 walkman

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

SRF-M80V Marketing

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands