manualshive.com logo in svg

Keysight DSOX3012T, User Manual

The Keysight DSOX3012T is a high-performance digital storage oscilloscope designed for precision measurements in a variety of applications. For detailed instructions on how to utilize all the features and functions of this device, you can download the user manual for free from manualshive.com.

Share
Download
background image

Getting Started

1

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

59

 

Learn the Oscilloscope Display

The oscilloscope display contains acquired waveforms, setup information, 

measurement results, and the softkey definitions.

1.

Power cord 

connector

Attach the power cord here.

2.

Kensington lock 

hole

This is where you can attach a Kensington lock for securing the instrument.

3.

Module slot

A DSOXLAN LAN/VGA module may be ordered and installed separately.

•

LAN port — lets you communicate with the oscilloscope and use the 

Remote Front Panel feature using the LAN port. See 

Chapter 23

, “Web 

Interface,” starting on page 359 and 

“Accessing the Web 

Interface"

on page 360.

•

VGA video output — lets you connect an external monitor or projector to 

provide a larger display or to provide a display at a viewing position 

away from the oscilloscope.
The oscilloscope's built-in display remains on even when an external 

display is connected. The video output connector is always active.
For optimal video quality and performance, we recommend you use a 

shielded video cable with ferrite cores.

A DSOXGPIB GPIB module may be ordered and installed separately.

4.

TRIG OUT 

connector

Trigger output BNC connector. See 

“Setting the Rear Panel TRIG OUT 

Source"

on page 350.

5.

Calibration 

protect button

See 

“To perform user calibration"

on page 352.

6.

EXT TRIG IN 

connector

External trigger input BNC connector. See 

“External Trigger Input"

on 

page 213 for an explanation of this feature.

7.

USB Host port

This port functions identically to the USB host port on the front panel. USB 

Host Port is used for saving data from the oscilloscope and loading 

software updates. See also USB Host port (see 

page 43

).

8.

USB Device 

port

This port is for connecting the oscilloscope to a host PC. You can issue 

remote commands from a host PC to the oscilloscope via the USB device 

port. See 

“Remote Programming with Keysight IO Libraries"

on 

page 366.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

Qingdao H.Y AP300 Manual preview
AP300
Brand: Qingdao H.Y Pages: 6
ABB AutoLink Mounting Instructions preview
AutoLink
Brand: ABB Pages: 11
Raytheon V700 Instruction Manual preview
V700
Brand: Raytheon Pages: 69
Galaxy Audio RM2 Operation Manual preview
RM2
Brand: Galaxy Audio Pages: 24
Panasonic WJHD309A - DIGITAL DISK RECORDER Network Operating Instructions preview
WJHD309A - DIGITAL DISK RECORDER
Brand: Panasonic Pages: 79
HAMAR LASER L-705 Manual preview
L-705
Brand: HAMAR LASER Pages: 49
Eastern Jungle Gym CLASSIC Owner'S Instruction Manual preview
CLASSIC
Brand: Eastern Jungle Gym Pages: 17
Vahle VCL Series Translation Of The Original Operating Instructions preview
VCL Series
Brand: Vahle Pages: 96
Daktronics Sportsound SSR-300 Operation Manual preview
Sportsound SSR-300
Brand: Daktronics Pages: 42
Garmin GPSMAP 188 Sounder Owner'S Manual And Reference Manual preview
GPSMAP 188 Sounder
Brand: Garmin Pages: 134
Idex Hale Sam Operation Installation Maintenance Manual preview
Hale Sam
Brand: Idex Pages: 141
IDEAL Networks SecuriTEST IP Quick Start Manual preview
SecuriTEST IP
Brand: IDEAL Networks Pages: 8
IDEAL Networks LanTEK IV Manual preview
LanTEK IV
Brand: IDEAL Networks Pages: 5
Maico MA 28 Operation Manual preview
MA 28
Brand: Maico Pages: 55
Maico easyTymp Operating Manual preview
easyTymp
Brand: Maico Pages: 38
Maico MA 42 Quick Manual preview
MA 42
Brand: Maico Pages: 2
MAHA Maschinenbau Haldenwang MBT Series Original Operating Instructions preview
MBT Series
Brand: MAHA Maschinenbau Haldenwang Pages: 13
Zennio KLIC-DI Installation Notes preview
KLIC-DI
Brand: Zennio Pages: 3

Brands by name

Popular brands

Load more brands