manualshive.com logo in svg

Keysight DSOX3012T, User Manual

The Keysight DSOX3012T is a high-performance digital storage oscilloscope designed for precision measurements in a variety of applications. For detailed instructions on how to utilize all the features and functions of this device, you can download the user manual for free from manualshive.com.

Share
Download
background image

352

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

22

Utility Settings

 

5

Press 

File Name

 to open the Remote Log Filename Menu where you can specify 

the name of the file (on the USB storage device) to which remote commands 

are logged.

6

Press 

Display On

 to enable or disable the screen display of logged remote 

commands and their return values (if applicable).

7

Press 

Transparent

 to disable or enable a transparent background for the remote 

command logging screen display.

Enable to make the background transparent. This lets you view underlying 

waveforms.

Disable for a solid background which makes the logged remote commands 

easier to read.

Performing Service Tasks

The Service Menu (under 

[Utility] > Service

) lets you perform service-related tasks:

•

“To perform user calibration"

on page 352

•

“To perform hardware self test"

on page 355

•

“To perform front panel self test"

on page 356

•

“To display oscilloscope information"

on page 356

•

“To display the user calibration status"

on page 356

For other information related to oscilloscope maintenance and service, see:
•

“To clean the oscilloscope"

on page 356

•

“To check warranty and extended services status"

on page 356

•

“To contact Keysight"

on page 357

•

“To return the instrument"

on page 357

To perform user calibration

Perform user-calibration:

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

OMCA 760 Use And Maintenance Manual preview
760
Brand: OMCA Pages: 36
Salford 699 Assembly And Parts Manual preview
699
Brand: Salford Pages: 64
ADVANCED HOME CARE Helios Manual preview
Helios
Brand: ADVANCED HOME CARE Pages: 16
Barco Coronis 5MP Mammo Brochure & Specs preview
Coronis 5MP Mammo
Brand: Barco Pages: 4
Barco CORONIS 1MP Installation & User Manual preview
CORONIS 1MP
Brand: Barco Pages: 167
Barco Color Coronis 2MP System Manual preview
Color Coronis 2MP
Brand: Barco Pages: 156
Barco Color Coronis 2MP Brochure & Specs preview
Color Coronis 2MP
Brand: Barco Pages: 12
Barco AMM240ED Operation Manual preview
AMM240ED
Brand: Barco Pages: 39
Barco SP4K-B Installation Manual preview
SP4K-B
Brand: Barco Pages: 158
Danelec DM800 Installation Manual preview
DM800
Brand: Danelec Pages: 67
XM Fitness XM100 Manual preview
XM100
Brand: XM Fitness Pages: 10
Haaga 677 Original Operating Instructions preview
677
Brand: Haaga Pages: 31
VBM POCKET Instructions For Use Manual preview
POCKET
Brand: VBM Pages: 36
W&H Med Lara Instructions For Use Manual preview
Lara
Brand: W&H Med Pages: 122
Pari mini Instructions For Use Manual preview
mini
Brand: Pari Pages: 50
Icare HOME Instruction Manual preview
HOME
Brand: Icare Pages: 42
Qlight SK Quick Start Manual preview
SK
Brand: Qlight Pages: 4
ZIEHL-ABEGG ZA top SM315.100A Original Operating Instructions preview
ZA top SM315.100A
Brand: ZIEHL-ABEGG Pages: 76

Brands by name

Popular brands

Load more brands