Keysight DSOX3012T User Manual Download Page 249

Page: 249 / 530

Measurements

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

249

When using the N2820A probe to make measurements on a battery-powered

(floating) device, always connect the supplied ground lead between ground on

your device and the probe's ground connector as shown in the following figure.

Simply snap the end of the ground lead onto the probe's connector. Without the

ground connection, the probe's common-mode input amplifier cannot properly

display waveforms.

Snapshot All

The Snapshot All measurement type displays a popup containing a snapshot of all

the single waveform measurements.

Charge

Charge (in Amp-hours) is the measured area under

the waveform. See

“Area"

on page 266.

Average

See

“Average"

on page 254.

Base

See

“Base"

on page 252.

Peak-Peak

See

“Peak-Peak"

on page 251.

DC RMS

See

“DC RMS"

on page 255.

AC RMS

See

“AC RMS"

on page 255.

Figure 46

Measurements on Battery Powered Devices Using the N2820A Probe

Dual-Channel (N2820A Probe)

Measurement

Notes

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands