background image

 

 

13/44 

Scienlab Regenerative AC Emulator 

 Keysight SL1200A Series 

 Operating Instructions 

User Information 

 

 

Without prior connection to a higher-level safety system, misuse can result in life-
threatening injuries. 

 

Keysight recommend first connecting the system to the higher-level safety and 
emergency stop system of the test bench, before putting it into operation. 

 

The Keysight emergency stop system in the control cabinet may not be 
changed or adapted without the consent of Keysight. 

Qualification of the Personnel 

Personnel

 

KeysightCare

 

Electrically 
trained persons

 

Trained persons 
with specialist 
training (me-
chanical/ elec-
trical engineer-
ing)

 

Activity

 

Transport

 

X

 

--

 

X

 

Connection and assembly

 

X

 

--

 

X

 

Commissioning

 

X

 

--

 

--

 

Operation

 

X

 

X

 

X

 

Maintenance

 

X

 

--

 

X

 

Replacement of system components

 

X

 

--

 

--

1

 

Troubleshooting

 

X

 

--

 

X

 

Disposal/recycling

 

X

 

--

 

X

 

Table 1: Qualification of personnel (X: permitted; --: not permitted) 
Electrically trained persons: 
Operator employees instructed and if necessary trained by KeysightCare 
or an electrician in the tasks assigned to them and the possible dangers of 
improper behavior as well as instructed in the necessary safety devices 
and safety measures. 
Trained persons with specialist training: 
Operator employees instructed by KeysightCare, who accept specialist 
and supervisory responsibility as electricians and are tasked with this 
function by the company. In terms of adherence to the electrotechnical 
safety specification, the responsible electrician must only receive instruc-
tion from other responsible electricians. 

(Definition example acc.to DGUV Regulation 3, DIN VDE 0105-100, EN 50110)

 

Contact KeysightCare 

 Technical Support 

Contact KeysightCare

 

 

Keysight Technologies Technical Support

 

www.keysight.com/find/keysightcare-contact

 

 

 

1

 Unless otherwise contractually (e. g. in the context of a spare parts package), all mechanical/electrical instal-

lations in or on the system must always be coordinated with Keysight. 

NOTICE 

Summary of Contents for SL1200A Series













































Reviews: