Keysight Technologies S9106AC-2IF Startup Manual Download Page 15 | Manualshive

Page: 15 / 80

background image

2 Review Safety Requirements

S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions, Startup Guide

11

2. 9 Power Requirements

100/120 VAC, 220/240 VAC

50/60 Hz

1200 W Max (Lower range), 1300 W Max (Upper range)

"WARNING: Safety of any system incorporating the equipment is
the responsibility of the assembler of the system."

The Keysight S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions
do not contain customer serviceable fuses.

Failure to ground the test set properly can result in personal
injury. Before turning on the test set, you must connect its
protective earth terminals to the protective conductor of the main
power cable. Insert the main power cable plug into a socket outlet
that has a protective earth contact only. DO NOT defeat the earth-
grounding protection by using an extension cable, power cable, or
auto-transformer without a protective ground conductor.

This instrument has auto-ranging line voltage input. Before
switching on the instrument, be sure the supply voltage is within
the specified range and voltage fluctuations do not exceed 10
percent of the nominal supply voltage.

«
...
13
14
15
16
17
...
»

Summary of Contents for S9106AC-2IF

















































































Reviews:

No comments

Related manuals for S9106AC-2IF

Endura AZ20 series

Brand: ABB Pages: 8

Brand: VeEX Pages: 2

Brand: Keithley Pages: 201

ORBISPHERE 3624

Brand: Hach Ultra Pages: 12

Monitoring System 500 II DC

Brand: Didactum Pages: 2

Pasport PS-2138

Brand: Pasco Scientific Pages: 26

Brand: bmcm Pages: 5

Brand: Tektronix Pages: 48

FG-3000R Series

Brand: Nidec Pages: 8

Brand: Victron energy Pages: 46

Energy Tech 401

Brand: CODEL Pages: 131

Brand: Bender Pages: 4

Brand: TEKELEK Pages: 3

Brand: Erma Electronic Pages: 24

Brand: Readiness Systems Pages: 16

Brand: MEWOI Pages: 21

Brand: Vega Pages: 24

Brand: Teledyne Analytical Instruments Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands