Keysight Technologies N9000A Installation Note Download Page 12 | Manualshive

Page: 12 / 14

Keysight Technologies N9000A Installation Note Download Page 12

12

Installation Note

N9000-90034

Option CR3 - Wideband IF Output Installation Kit

3. Update the Instrument Software

1. Loading the latest instrument software is required to assure all FPGAs and drivers located on both

the newly installed hardware and on the case instrument are synchronized. Therefore, even if the
instrument contains the latest revision of software, you must re-install the software to assure proper
operation.
The latest revision of software is available from:
http://www.agilent.com/find/Xseries_software

4. Install the License File

1. Located Option Upgrade Entitlement Certificate in the kit and follow the directions to redeem it.

You will receive and email with an attached license file.

2. Located the USB storage device. Perform a virus scan on this device before use. Save the license

file to the root directory of the USB storage device.

3. Connect the USB storage device to the signal analyzer USB port.

4. The signal analyzer will automatically consume the license file. This may take a few minutes.

When the license file is consumed, the Agilent License Manager will display a “Successful
License Installation” message as shown in

.

Figure 8

Successful License Installation

«
...
10
11
12
13
14
»

Summary of Contents for N9000A















Reviews:

No comments