Keysight Technologies N5290A Installation Manual Download Page 92

Page: 92 / 96

5-2 Keysight N5290/1A Installation Guide

Maintenance and Support
Maintenance

Maintenance

Physical Maintenance

Clean the cabinet, including the front panel, using a dry or slightly damp cloth

only.

Electrical Maintenance

Refer to

“Keysight Support, Services, and Assistance” on page 4-4

Caring for Waveguide (WG) Interfaces

A clean surface at millimeter-wave frequencies is much more important than at

lower frequencies because any debris on the waveguide surface can potentially

distort the measurement results.
Caring for WG interfaces is not difficult. Dirt and dust can be removed using

the following:

— Isopropyl alcohol 99.5%

— Lint-free cloth
— Pressurized air (for dust removal)
To remove dirt on the waveguide surface, simply put a few drops of isopropyl

alcohol on a lint-free cloth and gently wipe the surface.
To remove dust, simply spray the pressurized air on the waveguide surface.

Principles of Connector Care

Proper connector care and connection techniques are critical for accurate and

repeatable measurements. Refer to Table 5-1 for tips on connector care.
Prior to making connections to your analyzer, carefully review the information

about inspecting, cleaning, and gaging connectors. Refer to the calibration kit

documentation for detailed connector care information.
For course numbers about additional connector care instruction, contact

Keysight Technologies. Refer to

“Contacting Keysight” on page 4-4

To prevent electrical shock, disconnect the analyzer from the mains

source before cleaning. Use a dry cloth or one slightly dampened

with water to clean the external case parts. Do not attempt to clean

internally.

1. Use isopropyl alcohol only in a well-ventilated area. Allow all residual alcohol mois-

ture to evaporate, and the fumes to dissipate, prior to assembling waveguide inter-

faces.

Summary of Contents for N5290A

































































































Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands

Keysight Technologies N5290A, Installation Manual

Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands