Keysight Technologies N5290A Installation Manual Download Page 85

Page: 85 / 96

Keysight N5290/1A Installation Guide 4-11

Performance Verification
System Verification

performance is a significant contributor to the system performance, cables of

lower performance will increase the uncertainty of your measurement. It is

highly recommended that the test port cables be regularly tested.
If the system verification is performed with a non-Keysight cable, ensure that

the cable meets or exceeds the specifications for the test cable specified in the

previous table,

“Equipment Used in the System Verification Procedure.”

Refer

to the cable’s user’s guide for specifications.

Kit Substitution

Non-Keysight calibration kits and verification kits are not recommended nor

supported.

System Verification Procedure

If you desire printed test outputs, connect a printer to the analyzer. For the

printer, ensure that the correct driver is loaded and the printer is defined

as the default printer. Refer to the embedded help in the analyzer for

printer setup. Let the analyzer warm up for at least 90 minutes.

Insert the verification kit memory stick into the analyzer USB port.

Press

UTILITY

System

Service

System Verification

. The VNA System

Verification dialog box is displayed; refer to

Figure 4-3

Figure 4-3

System Verification Dialog Box

In the Calibration Kit box, select the calibration kit or electronic calibration

module (ECal) that is being used by clicking on it. The corresponding

verification kit to use is selected for you and displayed in the Verification

Kit box. Refer to

Figure 4-3

Summary of Contents for N5290A

































































































Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands

Keysight Technologies N5290A, Installation Manual

Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands