Keysight Technologies N5241AU-922 Manual Download Page 7

Page: 7 / 42

Installation Note N5242-90003 7

Description of the Upgrade
Getting Prepared

Tools Required for the Installation

About Installing the Upgrade

Description

Qty

Part Number

T-10 TORX driver (set to 9 in-lbs)

N/A

T-20 TORX driver (set to 21 in-lbs)

N/A

5/16-in torque wrench (set to 10 in-lbs)

N/A

5/16-in torque wrench (set to 21 in-lbs)

N/A

Use a 5/16-in torque wrench set to 10 in-lbs on all cable connections

except the front and rear panel cable connectors. Torque these

connections to 21 in-lb.

Products affected

N5241A, N5242A and N5249A Option 219

Installation to be performed by

Keysight service center or personnel qualified by Keysight

Estimated installation time

5.0 hours

Estimated adjustment time

0.5 hours

Estimated full instrument calibration time

4.5 hours

Summary of Contents for N5241AU-922











































Search results

Summary of Contents for N5241AU-922

Reviews:

Related manuals for N5241AU-922

Brands by name

Popular brands

Keysight Technologies N5241AU-922, Manual

Search results

Summary of Contents for N5241AU-922

Reviews:

Related manuals for N5241AU-922

Brands by name

Popular brands