Keysight Technologies N5221BU-605 Installation Note Download Page 73

Page: 73 / 88

Installation Note N5222-90114 73

Installation Procedure for the Upgrade

Step 46. DC Continuity Test the LFE Board and Test Ports

The DC continuity test verifies that the LFE board is installed correctly and

does not have any opens or shorts in the DC path.

Using a DVM, connect one test probe to the center conductor of the RF

port 1 on the front panel.

Connect the other test probe to the port 1 bias input (

BIAS 1 IN

) on the

rear panel.

Verify the DVM measures

10Ω.

Repeat these steps for each of the other test ports.

Step 47. Position the Cables and Wires to Prevent Pinching

On the top side of the PNA, carefully position the gray flex cables so they can’t

be pinched between the covers and the rails.
On the bottom side of the PNA, carefully fold or push down the ribbon cables

and wires so they can’t be pinched between the hardware and the outer cover.
Ribbon cables and wires must never be positioned on top of hardware.

Step 48. Reinstall the Inner Cover

For instructions, click the Chapter 7 bookmark “Removing the Covers” in the
PDF Service Guide

Step 49. Reinstall the Outer Cover

For instructions, click the Chapter 7 bookmark “Removing the Covers” in the
PDF Service Guide

If the DVM value is 0Ω or

10Ω, then something is incorrectly installed or

there is an open or short somewhere in the LFE board/cable path:

—

Verify the cables installed in

“Step 47. Position the Cables and Wires

to Prevent Pinching” on page 73

and

“Step 40. Install/Reinstall the

A71–74 and Bias-Tee Combiner’s Gray Low Frequency Extension

(LFE) DC bias Cables and Route Cables” on page 68

are connected

correctly and not open or shorted.

Summary of Contents for N5221BU-605

























































































Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands

Keysight Technologies N5221BU-605, Installation Note

Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands