Keysight Technologies N5221BU-605 Installation Note Download Page 18

Page: 18 / 88

Installation Note N5222-90114

Installation Procedure for the Upgrade

Step 4. Inspect and (If Necessary) Remove the A4, A11, and A13

Synthesizer Boards, if They Are Not Version H

Verify that the synthesizer boards are all version H or greater.

If your synthesizer boards are all H or greater, on the PNA: Press

Utility

System

Service

Utilities

View EEPROM Headers

Verify the LO Synthesizer, Src1 Synth, and Src2 Synth boards are all

version H or greater.

Refer to

Figure 2 on page 18

Figure 2

EERPOM Header Info Window

The N5240-60074 (with tabs) or N5240-60076 (without tabs) pretested

synthesizer boards will both show

Board P/N: N5240-63074

in the

EEPROM window (as shown in

Figure 2 on page 18

If the synthesizer board part number displayed in the EEPROM Header

window is not N5240-63074 (e.g. N5242-63150), you will need to order

new synthesizer boards. Refer to

“Contacting Keysight” on page 4

. Refer

“Contacting Keysight” on page 4

Summary of Contents for N5221BU-605

























































































Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands

Keysight Technologies N5221BU-605, Installation Note

Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands