Keysight Technologies N5221B Manual Download Page 68

Page: 68 / 88

68 Installation Note N5222-90131

Description of the Upgrade
Installation Procedure for the Upgrade

Reinstall N5240-60097 (x1), N5240-60098 (x1), and Install New

N5240-60098 (x2) Blue Bias-Tee Combiner Cables from the A71–A74

Bias Tees "RF-IN" to the A70 LFE Board "Port1", "Port2", "Port3", and

"Port4" Connectors and Install Clamps onto the Ferrite Beads

Reinstall the N5240-60097 (x1), N5240-60098 (x1), and install the NEW

N5240-60098 (x2) cable as shown. Note the orientation of the cable (item

①

through

➂

). Torque to 10 in-lbs. Refer to

Figure 41

and

Figure 42 on

page 69

Figure 41

Verify N5240-60097 A74 (Port 2) and connect new N5240-60098 A73 (Port 4)

Bias Tee Combiner to A70 LFE Board and Install Clamps on Ferrite Beads

(N5240-60097 (x1), N5240-60098 (x1), and 1400-1391 (x2))

Verify Port

2 cable is

properly

routed and

secured.

Summary of Contents for N5221B

























































































Search results

Summary of Contents for N5221B

Reviews:

Related manuals for N5221B

Brands by name

Popular brands

Keysight Technologies N5221B, Manual

Search results

Summary of Contents for N5221B

Reviews:

Related manuals for N5221B

Brands by name

Popular brands