Keysight Technologies N5221A Service Manual Download Page 48

Page: 48 / 368

3-20 Keysight N5221A/22A Service Guide

Tests and Adjustments
Preliminary Checks

10.

To re-normalize the data trace of the reconnected cable: press
MARKER/ANALYSIS

, then

, then ENTRY

11.

Repeat steps 7 through 9 at least three times to look for modes. Modes

appear when a harmonic of the source fundamental frequency is able to

propagate through the cable or connector. It is helpful to print a plot of the

trace each time to compare several connections. If any mode appears

each time the cable is connected and reconnected, measurement integrity

will be affected.
For a typical response of cable connector repeatability, see

Figure 3-8

12.

For the Port 2, 3, and 4 Check, connect the cable (with the load attached)

to the respective port and repeat steps 2 through 11.

Figure 3-8

Typical Cable Connector Repeatability Response

If the Cable Connector Repeatability Check Fails

Clean the cable and devices, and torque to specification. Repeat the

check.

If the check still fails, the cable should be repaired or replaced.

Memory

Data->Memory

Enter

Summary of Contents for N5221A

















































































































































































































































































































































































Search results

Summary of Contents for N5221A

Reviews:

Keysight Technologies N5221A, Service Manual, Page: 48 / 368

Search results

Summary of Contents for N5221A

Reviews: