Keysight Technologies N5221A Service Manual Download Page 172

Page: 172 / 368

6-16 Keysight N5221A/22A Service Guide

Replaceable Parts
Replaceable Parts Listings

Top Assemblies and Cables, All Options

Top Assemblies, All Options

When replacing an old assembly, install an assembly with either the same

part number or the new part number.

Reference

Designator

Part Number

Qty

Description

N5240-60074

Was N5242-60150

13.5 GHz (source 1) synthesizer board

5087-7342

26.5 GHz source (1) board

Not used.

5087-7342

26.5 GHz source (2) board

Not used.

A10

N5240-60069

Was N5240-60061

Frequency reference board

A11

N5240-60074

Was N5242-60150

13.5 GHz (LO) synthesizer board

A12

N5240-60077

Was N5240-60056

Signal Processing ADC Module (SPAM) board

A13

N5240-60074

Was N5242-60150

13.5 GHz (source 2) synthesizer board

A14

N5242-60151

System motherboard

A15

W1312-60095

Midplane board

A16

0950-4934

Power supply

A17

W1312-60196

CPU board assembly, Intel ® 2.0 GHz Core ® i7

A18

N5240-60059

GPIB board

A51

N5242-60088

Solid state drive (SSD) for Windows XP Operating System- to be used
with the 2.0 GHz CPU board W1312-60196, System CPU version 6

N8983A

Solid state drive (SSD) for Windows 7 Operating System- to be used
with the 2.0 GHz CPU board W1312-60196, System CPU version 6

1420-0356

Battery, lithium manganese dioxide, 3V, 0.22A-hr.

a. For the latest information on CPUs and associated drives, visit:

http://na.support.keysight.com/pna/hdnum-

bers.html

b. The A51 solid state disk drive for the 2.0 GHz CPU board plugs into the A21 CPU board assembly from the rear panel. Refer

“Removing and Replacing the A51 Solid State Drive (SSD)” on page 7-50

for an illustration.

Summary of Contents for N5221A

















































































































































































































































































































































































Search results

Summary of Contents for N5221A

Reviews:

Keysight Technologies N5221A, Service Manual, Page: 172 / 368

Search results

Summary of Contents for N5221A

Reviews: