manualshive.com logo in svg

Keysight Technologies N5221A, Service Manual, Page: 103 / 368

Share
Download
Keysight Technologies N5221A Service Manual Download Page 103

Keysight N5221A/22A Service Guide                                                                                            4-29

Troubleshooting
Measurement System Troubleshooting

EEPROM Headers

The network analyzer application uses the firmware revision information stored 

in the pc board header EEPROM. If the information stored in any EEPROM is 

incorrect, the network analyzer may not operate properly.
The following link lists the pc boards in your network analyzer that contain 

EEPROM headers. The pc boards are listed by name and part number and the 

correct firmware revision code is given for each. Refer to:

 

http://na.support.keysight.com/pna/EEPROM_Information.html

.

To view this EEPROM header information on the network analyzer display: 
press UTILITY 

, then 

 , then 

 , then 

 .  Refer  to 

Figure 4-6

.

If the information is incorrect for any of the PC boards, contact Keysight 

Technologies. Refer to 

“Contacting Keysight” on page 2-7

.

Figure 4-6 

EEPROM Header Info Dialog Window

Error Messages

SOURCE UNLEVELED: 

The source ALC circuit on the A19 test set motherboard 

is running open-loop. Check the cable connections for the A21 HMA26.5 and 

the A19 test set motherboard.

Verifying the A, B, C, D, and R Traces (Standard S-Parameter Mode)

The first step is to verify that the A, B,C, D, and R traces are present and that 

they are approximately level:

System

Service

Utilities

View EEPROM Headers

Summary of Contents for N5221A

















































































































































































































































































































































































Reviews:

No comments