Keysight Technologies InfiniiVision 3000 X Series User Manual Download Page 361

Page: 361 / 432

361

Keysight InfiniiVision 3000 X-Series Oscilloscopes

User's Guide

24 FlexRay Triggering and

Serial Decode

Setup for FlexRay Signals / 361
FlexRay Triggering / 362
FlexRay Serial Decode / 365

The FlexRay triggering and serial decode option is license-enabled.

Setup for FlexRay Signals

FlexRay signal setup consists of first connecting the oscilloscope to a differential

FlexRay signal using a differential active probe (the Keysight N2792A is

recommended), specifying the signal source, threshold voltage trigger level, baud

rate, and bus type.

To set up the oscilloscope to capture FlexRay signals:

Press

[Label]

to turn on labels.

Press

[Serial]

Press the

Serial

softkey, turn the Entry knob to select the desired serial bus

(Serial 1 or Serial 2), and press the softkey again to enable decode.

Press the

Mode

softkey; then, select

FlexRay

mode.

Press the

Signals

softkey to open the FlexRay Signals Menu.

Summary of Contents for InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands

Keysight Technologies InfiniiVision 3000 X Series, User Manual

Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands