Keysight Technologies Infiniium MSOV 084A Service Manual Download Page 139 | Manualshive

Page: 139 / 164

background image

Replaceable Parts

6

Infiniium V-Series Oscilloscopes Service Guide

139

Replaceable Parts List

The following table is a list of replaceable parts. The information given for each

part includes:
• Reference designation in exploded views
• Keysight part number
• Total quantity (QTY) in the oscilloscope or an assembly
• Description of the part

Replaceable parts

Ref. Des Part number

Qty

Description

A1

2090-1099

1

Display - LCD 12.1-in. backlit w/capacitive touch screen

A2

08673-67601

1

Connector assembly - output

A3

54919-66406

1

PCA - On/off board

A4

54916-66414

1

PCA - Autoprobe board

A5

5062-1247

1

Assembly - 3.5 mm connector

A6

54919-66405

1

PCA - keyboard

A7

33325-60024

1

Step attenuator - front panel (RoHS version of 33325-60013)

A8

54919-00104

1

Chassis

A9

54919-66721

2

Acquisition PCA, usable for up to and including 33 GHz -

tested

A9

54919-69721

2

Acquisition PCA, usable for up to and including 33 GHz -

exchange

A9

54919-66731

1

Tested acquisition board, usable for 25, 20, 16, 13, or 8 GHz

A9

54919-69731

1

Tested acquisition board, usable for 25, 20, 16, 13, or 8 GHz -

exchange

A9

54916-00502

2

Frame for acquisition assembly

A10

N2834-66501

1

Printed circuit board for MSO models - loaded and tested

A10

N2834-69501

1

Printed circuit board for MSO models - exchange

A11

54919-66501

1

Hardware serial trigger PCA - tested

A11

54919-69501

1

Hardware serial trigger PCA - exchange

A12

54916-66533

1

Backplane PCA - tested

A12

54916-66733

1

Backplane PCA for MSO models - tested

A12

54916-69733

1

Backplane PCA for MSO models - exchange

A13

54913-68710

1

Fan replacement kit 120 mm

«
...
137
138
139
140
141
...
»

Summary of Contents for Infiniium MSOV 084A





































































































































































Reviews:

No comments

Related manuals for Infiniium MSOV 084A

Brand: Rain-Flo Irrigation Pages: 20

Attest Auto-reader 390

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 2

PELTOR WS LiteCom Plus

Brand: 3M Pages: 7

Steri-Vac GS Series

Brand: 3M Pages: 52

Brand: Gardena Pages: 8

Brand: GARANT Pages: 239

Brand: p-light Pages: 36

Brand: Tascam Pages: 8

Brand: Malekko Pages: 2

Brand: Major Pages: 26

Brand: +GF+ Pages: 2

Unity for Pro-Flex Pivot

Brand: Össur Pages: 40

ICELOCK 234 LANYARD

Brand: Össur Pages: 94

Brand: Össur Pages: 115

Brand: Össur Pages: 253

Brand: Posture Pump Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands