manualshive.com logo in svg

Keysight Technologies DSO-X 2014A, User Manual

The Keysight Technologies DSO-X 2014A is a high-performance oscilloscope designed for accurate measurements and analysis. To make the most of its features, be sure to download the free User Manual from manualshive.com. This manual provides detailed instructions on how to operate and maximize the capabilities of this powerful tool.

Share
Download
background image

269

Keysight InfiniiVision 2000 X-Series Oscilloscopes 

User's Guide

 

19 Print (Screens)

To print the oscilloscope's display / 269
To set up network printer connections / 270
To specify the print options / 272
To specify the palette option / 272

You can print the complete display, including the status line and softkeys, to a 

USB printer or a network printer when the DSOXLAN LAN/VGA module is 

installed.

The Print Configuration Menu is displayed when you press the 

[Print]

 key. The print 

option softkeys and the 

Press to Print

 softkey are ghosted (not available) until a 

printer is connected.

To print the oscilloscope's display

1

Connect a printer. You can:

•

Connect a USB printer to either the USB port on the front panel or the 

rectangular USB host port on the rear panel.

For the most up-to-date listing of printers that are compatible with the 

InfiniiVision oscilloscopes, please visit 

www.keysight.com/find/InfiniiVision-printers

.

•

Set up a network printer connection. See 

"To set up network printer 

connections"

on page 270.

2

Press the 

[Print]

 key on the front panel.

3

In the Print Configuration Menu, press the 

Print to

 softkey; then, turn the Entry 

knob to select the desired printer.

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Reviews:

No comments

Related manuals for DSO-X 2014A

Tanco A Series Operator'S Handbook Manual preview
A Series
Brand: Tanco Pages: 72
HABYS Aero Instruction Manual & Warranty preview
Aero
Brand: HABYS Pages: 16
Acterna A Series Operating Manual preview
A Series
Brand: Acterna Pages: 72
Rapid Technic Mondo Operating Manual preview
Mondo
Brand: Rapid Technic Pages: 152
YYZ Lighting LYNX Installation preview
LYNX
Brand: YYZ Lighting Pages: 3
Camp Safety COBRA Manual preview
COBRA
Brand: Camp Safety Pages: 118
Ultrafast Systems KRONOS User Manual preview
KRONOS
Brand: Ultrafast Systems Pages: 39
Mackworth HOLLY User Instructions preview
HOLLY
Brand: Mackworth Pages: 2
CAMPAGNOLA COBRA PRO Use And Maintenance Manual preview
COBRA PRO
Brand: CAMPAGNOLA Pages: 209
TATU PT Operator'S Manual preview
PT
Brand: TATU Pages: 30
Rane HC6S Operator'S Manual preview
HC6S
Brand: Rane Pages: 4
Sabio 2010D Operation Manual preview
2010D
Brand: Sabio Pages: 182
Varimixer ERGO60 Operating Instructions Manual preview
ERGO60
Brand: Varimixer Pages: 28
ABB TPL85-B12 Operation Manual preview
TPL85-B12
Brand: ABB Pages: 154
Life Fitness CS45X Assembly Instructions Manual preview
CS45X
Brand: Life Fitness Pages: 8
Moticon OpenGo Instructions Manual preview
OpenGo
Brand: Moticon Pages: 24
Zempire Evo TM/TSV2 Awning Wall Set Instructions preview
Evo TM/TSV2 Awning Wall Set
Brand: Zempire Pages: 2
GERATHERM UniqueTemp Instruction Manual preview
UniqueTemp
Brand: GERATHERM Pages: 40

Brands by name

Popular brands

Load more brands