manualshive.com logo in svg

Keysight Technologies DSO-X 2014A, User Manual

The Keysight Technologies DSO-X 2014A is a high-performance oscilloscope designed for accurate measurements and analysis. To make the most of its features, be sure to download the free User Manual from manualshive.com. This manual provides detailed instructions on how to operate and maximize the capabilities of this powerful tool.

Share
Download
background image

177

Keysight InfiniiVision 2000 X-Series Oscilloscopes 

User's Guide

 

12 Acquisition Control

Running, Stopping, and Making Single Acquisitions (Run Control) / 177
Overview of Sampling / 178
Selecting the Acquisition Mode / 183
Acquiring to Segmented Memory / 189

This chapter shows how to use the oscilloscope's acquisition and run controls.

Running, Stopping, and Making Single Acquisitions (Run Control)

There are two front panel keys for starting and stopping the oscilloscope's 

acquisition system: 

[Run/Stop]

 and 

[Single]

.

• When the 

[Run/Stop]

 key is green, the oscilloscope is running, that is, acquiring 

data when trigger conditions are met.

To stop acquiring data, press 

[Run/Stop]

. When stopped, the last acquired 

waveform is displayed.

• When the 

[Run/Stop]

 key is red, data acquisition is stopped.

"Stop" is displayed next to the trigger type in the status line at the top of the 

display.

To start acquiring data, press 

[Run/Stop]

.

• To capture and display a single acquisition (whether the oscilloscope is running 

or stopped), press 

[Single]

.

The 

[Single]

 run control lets you view single-shot events without subsequent 

waveform data overwriting the display. Use 

[Single]

 when you want maximum 

memory depth for pan and zoom.

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Reviews:

No comments

Related manuals for DSO-X 2014A

Landoll 7812 Operator And Parts Manual preview
7812
Brand: Landoll Pages: 52
Gason 7390 Operator'S Manual preview
7390
Brand: Gason Pages: 110
Gainsborough K900 Instructions For Use preview
K900
Brand: Gainsborough Pages: 2
Panasonic LP-GS Series Serial Communication Command Manual preview
LP-GS Series
Brand: Panasonic Pages: 180
Rainbow Quantum Instruction Manual preview
Quantum
Brand: Rainbow Pages: 18
Xo FLEX Installation Instructions Manual preview
FLEX
Brand: Xo Pages: 59
Falcon HT2 Installation And Servicing Instructions preview
HT2
Brand: Falcon Pages: 8
Velleman HQ Power VDL25BM Quick Start Manual preview
HQ Power VDL25BM
Brand: Velleman Pages: 3
iGuzzini Whisper Manual preview
Whisper
Brand: iGuzzini Pages: 36
Waterous AQUIS ULTRAFLOW Installation And Operation Manual preview
AQUIS ULTRAFLOW
Brand: Waterous Pages: 56
Ideal Heating EVOMAX 2 30 Manual preview
EVOMAX 2 30
Brand: Ideal Heating Pages: 16
TANNER Scientific Cryostat TN60 Operating Instructions Manual preview
Cryostat TN60
Brand: TANNER Scientific Pages: 44
Ebyte E78-915TBL-02 User Manual preview
E78-915TBL-02
Brand: Ebyte Pages: 7
Beurer FM 150 Instructions For Use Manual preview
FM 150
Brand: Beurer Pages: 21
SCHUNK PFH 30 Assembly And Operating Manual preview
PFH 30
Brand: SCHUNK Pages: 35
Honestech 3.0 Plus User Manual preview
3.0 Plus
Brand: Honestech Pages: 43
Southern States EC-1V Installation Instructions Manual preview
EC-1V
Brand: Southern States Pages: 36
SOMFY CONTROL4 Programming Manual preview
CONTROL4
Brand: SOMFY Pages: 10

Brands by name

Popular brands

Load more brands