Keysight Technologies B1505A Configuration Manual Download Page 87

Page: 87 / 298

Keysight B1505A Configuration and Connection Guide

2-5

N1259A Connection Guide

Input Connection

Table 2-1

To Connect between B1505A and N1259A, without HVMCU and Module Selector

B1505A terminals

Required cables

N1259A terminals

Interlock

16493J Interlock cable, 3 m or 1.5 m, 1 ea.

Interlock

GNDU

16493L GNDU cable, 3 m or 1.5 m, 1 ea.

GNDU1

1. If the N1266A expander is used, connect the 16493L-001 cable from the N1266A Output Low.

HVSMU

Force

16493T HVSMU cable, 3 m or 1.5 m, 1 ea.

HVSMU1

2. If the N1266A expander is used, connect the 16493T-001 cable from the N1266A Output High.

HCSMU

DHCSMU

Force

For HCSMU, 16493S HCSMU cable, 3 m or 1.5 m, 1 ea.

For DHCSMU, 16493S HCSMU cable, 3 m or 1.5 m, 1 ea., and
16493S-021 Dual HCSMU adapter. See

"To Connect

16493S-021" on page 5-22

for Dual HCSMU adapter.

HCSMU1

HCSMU2

Force

Sense

MCSMU

Force

16494A Triaxial cable, 3 m or 1.5 m, 1 ea. and N1254A-104
Triaxial(f)-BNC(m) adapter, 1 ea.

HCSMU1

HCSMU2

Force

Sense

16494A Triaxial cable, 3 m or 1.5 m, 1 ea.

Sense

HPSMU

MPSMU

Force

16494A Triaxial cable, 3 m or 1.5 m, 1 ea., for the non-Kelvin
connection, connect it between the Force connectors.

For the Kelvin connection, prepare additional one more cable and
connect it between the Sense connectors. Or use 16493K Kelvin
triaxial cable instead of 16494A.

HPSMU1

HPSMU2

Force

Sense

MFCMU

Hpot/

Hcur

N1300A CMU cable, 3 m or 1.5 m, 1 ea.

BNC(m)-(f)-(f) adapter, total 2 ea., 1 ea. for connecting Hpot,
Hcur, and AUX1, and 1 ea. for connecting Lpot, Lcur, and
AUX2.

It is not needed to connect the ground wire extended from the
CMU cable.

AUX 1

Lpot/

Lcur

AUX 2

MFCMU

Hpot

N1300A CMU cable, 3 m or 1.5 m, 1 ea.

It is not needed to connect the ground wire extended from the
CMU cable.

MFCMU

Only for

N1259A-

020

Hpot

Hcur

Lcur

Lpot



BNC cable, for connecting instruments other than the B1505A

AUX 1 or 2

Summary of Contents for B1505A











































































































































































































































































































Search results

Summary of Contents for B1505A

Reviews:

Brands by name

Popular brands

Keysight Technologies B1505A, Configuration Manual

Search results

Summary of Contents for B1505A

Reviews:

Brands by name

Popular brands