manualshive.com logo in svg

Keysight Technologies B1505A, Configuration Manual

Share
Download
Keysight Technologies B1505A Configuration Manual Download Page 170

5-22

Keysight B1505A Configuration and Connection Guide

Connection Guide for Wafer Prober and Your Own Test Fixture
To Connect Dual HCSMU Adapter

To Connect 16493S-021

The 16493S-021 adapter is used with an accessory, 16493S-010/011 HCSMU adapter, 
N1258A module selector, or N1259A/N1265A test fixture. The adapter should be installed 
near the accessory.

Table 5-14

To Connect 16493S-021 Input

Table 5-15

To Connect 16493S-021 Output

CAUTION

If DHCSMU is used with the N1258A or N1259A-300 module selector, the maximum 
current must be ± 30 A to prevent the module selector from performance degradation and 
failure.

B1505A terminals

Required cables Input 

terminals

 HCSMU 

used for 

master

Force

16493S HCSMU cable, 3 m or 1.5 m

Master

Force

Sense

Sense

HCSMU 

used for 

slave

Force

16493S HCSMU cable, 3 m or 1.5 m

Slave

Force

Sense

Sense

Output terminals

1

 

1. This is the DHCSMU channel. The connectors are compatible with HCSMU.

Required cables/Description

Connect to

Output

Force

dedicated cable, 300 mm, furnished with 16493S-021

To connect N1265A, adapters N1254A-103 for Force and 
N1254A-517 for Sense are required.

HCSMU input 

connectors of 

16493S-010/011, 

N1258A, N1259A, 

or N1265A

Sense

16493S 

Opt 021

Dual HCSMU Combination Adapter

Force

Sense

High Sense

Low Sense

HCSMU

Circuit

Common

High Force

Low Force

±

40 V     Max

Output

Sense

Force

Sense

Force

Master

Slave

From HCSMU

Summary of Contents for B1505A











































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands