Keysight Technologies B1505A Configuration Manual Download Page 260

Page: 260 / 298

7-42

Keysight B1505A Configuration and Connection Guide

Connection and Ordering Examples
Configuration Examples for Lateral Device Measurement with Wafer Prober

3 kV, 500 A, High Voltage Medium Current Measurement for
On-Wafer Lateral Device

•

Device Type: Lateral MOSFET (4 terminals)

•

Key Specification

•

Max voltage/current: 3 kV/500 A

•

High Voltage Medium Current capability: 2200 V/1.1 A, 1500 V/2.5 A

•

Module Selector for multi-parameter automated measurement function

Figure 7-22

Connection example

NOTE

Prober vendor is responsible for cabling inside the shielding box.

Table 7-20

Ordering example

Model/Option

Quantity

Description

B1505A

Power Device Analyzer/Curve Tracer mainframe

B1513C-FG

High Voltage Source Monitor Unit, 3000 V/4 mA (Pulsed & DC)

B1514A-FG

Medium Current Source Monitor Unit, 1 A/30 V(Pulsed), 100 mA/30 V(DC)

16493T

High Voltage Source Monitor Unit Cable

16493T-001 or
002

High Voltage Source Monitor Unit Cable (1.5 m or 3.0 m)

16493L

Ground Unit Cable

N1266A

HVSMU

GNDU

MCSMU

B1505A

MCSMU

16493J Interlock cable (Included in B1505A)

GNDU

Input Output

Input
HVSMU

Output

High

Output

Low

F
S

F
S
F
S

Vcontrol F

Vcontrol S

Icontrol F

Icontrol S

F
S

16493G-001Digital I/O cable (Included in N1266A)

HVSMU

GNDU

UHC Input
V Control

I Control

For Gate

For N1265A

For Drain

For N1266A

ate

N1265A

Gate

Selector

High

Low

MCSMU

F
S

N1254A-524

16493G-001 Digital I/O cable (Included in N1265A)

Chuck

For Chuck

Gate F
Gate S

16493L

16493T (Included in the HVSMU)

16494A (Included in the MCSMU)

16493L
(Included in B1505A)

16494A

(Included in the MCSMU)

16493T

16494A (Included in the MCSMU)

HCSMU Non-

Kelvin adapter

16493S-011

N1254A-104 TRX(J) to BNC(P) adapter

16493U-001

1250-2405

Summary of Contents for B1505A











































































































































































































































































































Search results

Summary of Contents for B1505A

Reviews:

Related manuals for B1505A

Brands by name

Popular brands

Keysight Technologies B1505A, Configuration Manual

Search results

Summary of Contents for B1505A

Reviews:

Related manuals for B1505A

Brands by name

Popular brands