manualshive.com logo in svg

Keysight Technologies B1505A, Configuration Manual

Share
Download
Keysight Technologies B1505A Configuration Manual Download Page 131

Keysight B1505A Configuration and Connection Guide

3-25

N1265A Connection Guide

Output Connection

Figure 3-15

To Install Resistor in the N1265A-035 Universal R-Box, Connection for Case 1

Protection Adapter (N1265A-040)

This is the adapter for protecting SMU from ultra high voltage.

If a SMU is used for the gate drive when performing the ultra high voltage measurement 
using UHVU, this adapter must be connected to the SMU terminals for preventing SMU 
from damage. See 

Figure 3-6

 for connection example.

This adapter is designed for using the MCSMU. 

Container (N1265A-045)

This container can accommodate protection adapters and bias-tee which are used with the 
N1265A to make the measurement environment clean and safe.

Maximum superimposed load is 50 kg. The N1265A and the N1266A can be put on the top 
of the container.

Prober System Cable (N1254A-524)

This is the cable for extending the N1265A’s Selector Output and Gate terminals to a 
prober station. See 

"To Connect Ultra High Current Expander" on page 5-36

 for more 

information.

CAUTION

Do not apply voltage/current over the maximum limit of the cable. See 

Table 5-28

.

High Force

Low Force

High Sense

Low Sense

High

Low

Summary of Contents for B1505A











































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands