manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 29

Electronic Calibration Modules Reference Guide                                                                               1-21

General Information
Compatible Network Analyzers

Compatible Network Analyzers

ECal modules operate with the network analyzer models shown in 

Table 1-9

, 

Table 1-10 on page 23

, 

Table 1-11 on page 25

, and 

Table 1-12 on page 27

. 

Not all ECal module and network analyzer combinations have the same 

features or capabilities. See your network analyzer user guide or online Help.

 

Table 1-9 

8509

xD Compatible Network Analyzers

Network

Analyzers

85091D/85092D/85093D/

 

85094D/85096D/85098D/

 

85099D ECal Module Series

Interface

Required 

a

(Required VNA firmware 
revision)

b

PNA Network Analyzers

N522xA, N523xA, N524xA

Yes 

 

(

≥

A.10.49.07)

USB

N522xB, N523xB, N524xB

Yes

USB

ENA Network Analyzers

E5061B

Yes

 

(

≥

B.05.02)

USB

E5063A

Yes

 

(

≥

A.05.06)

USB

E5071C

Yes

 

(

≥

B.14.03)

USB

E5072A

Yes

 

(

≥

B.02.44)

USB

E5080A

Yes

 

(

≥

A.12.60.03)

USB

 

E5080B

Yes

USB

PXIe Vector Network Analyzer Modules

M937xA Yes

 

(

≥

A.12.60.02)

USB

M9485A

Yes

 

(

≥

A.12.60.02)

USB

M980xA

Yes

USB

Streamline Vector Network Analyzer Modules

P937xA

Yes

USB

P937xB, P938xB

Yes

USB

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands