manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 12

 1-4                                                                                Electronic Calibration Modules Reference Guide

General Information
Models and Options

1-

Models and Options

This section provides the model number, operating characteristics and 

connector options available with Keysight RF and microwave ECal modules. 

You can order ECal modules by selecting the model number followed by the 

desired options. 

 8509xD Modules (RF Two-Port)

ECal modules from this series are available with the connector types and 

frequency ranges shown in 

Table 1-2 on page 1-10

. Mixed connector options 

allow you to configure the module with a different connector type at each port 

(as shown in 

Figure 1-9

). 

Figure 1-1 

Model 85091D Option 7 mm shown

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands