Keys Fitness Power Tower ST-PT Series Owner'S Manual Download Page 3

Safety Precautions and Tips

It is the owner's responsibility to ensure that all users of this

exercise unit have read the Owner's Manual and are familiar with
warnings and safety precautions.

• This strength training unit has a user maximum capacity of 

250 lbs pounds.

• It should only be used on a level surface and is intended for

indoor use only. It should not be placed in a garage, patio or
near water.

• Wear comfortable, good-quality walking or exercise shoes and

appropriate clothing. Do not use this exercise unit with bare
feet, sandals, socks or stockings!

• Always examine your strength training unit  before using to

ensure all parts are in working order.

• Do not leave children unsupervised near or on the exercise unit.

• Service to your Keys strength training unit should only be 

performed by an authorized service representative, unless
authorized and/or instructed by a Keys technician. Failure 
to follow these instructions will void the warranty.

2

3

Before You Start

Thank you for purchasing a Keys Strength Trainer Unit! This

quality product you have chosen  was designed to meet your
needs for strength training exercise.

Prior to assembly, remove components from the box and verify

that all the listed parts were supplied. Assembly instructions are
described in the following steps and illustrations.

Important Safety Information

WARNING!

1) Before using this exercise unit or starting any exercise 

program, consult your physician. This is especially important
for persons over the age of 35 and/or persons with pre-
existing health problems. Keys Fitness Products LP assumes 
no responsibility for personal injury or property damage 
sustained by or through the use of this product.

2) To reduce the risk of possible injuries to the user, it is 

important to review this manual and the following 
precautions before operation.

Summary of Contents for Power Tower ST-PT Series












Reviews: