manualshive.com logo in svg

Kewtech KT63 PLUS, Operating Instructions Manual

Share
Download
Kewtech KT63 PLUS Operating Instructions Manual Download Page 2

kewtechcorp.com

2

Index

Safety information and explanation of symbols used ..................................4

Contents of the KT63 PLUS .......................................................................5

Inserting Batteries ....................................................................................7

Overview ..................................................................................................8

Rotary Switch Functions ............................................................................9

Push Button Functions .............................................................................10

Continuity Test Function ..........................................................................10

Insulation Test Function ...........................................................................13

Special Polarity Test Pad .........................................................................16

Loop Test Function ..................................................................................17

RCD Test Function ...................................................................................23

Phase Rotation .......................................................................................27

Specifications and Tolerances .................................................................28

Summary of Contents for KT63 PLUS

































Reviews:

No comments

Brands by name

Popular brands

Load more brands