background image

OSF-5-BA-e-1510 

 

18 

Angle table 

 

      

 

 

Standard angle table 

 

 

 

Angle table for using transmitted light 

 
 
For easier handling of  an object  to be observed,  it can be useful to fit an additional 
mechanical angle table on the working surface of a stereo microscope.  
 
For  devices  without  lighting  you  can  use  a  standard  angle  table 

(see  left  figure)

However  if  there  is  an  integrated  transmitted  lighting  unit,  you  should  use a  special 
angle table with transmitted light compatibility (

see right figure

). 

 
As  the  figures  show,  both  versions  each  have  two  coaxially  positioned  adjustment 
wheels in the righthand rear corner of the table. This means that you can move it in 
the x and y directions. 
 
 
To  fit  this,  the  user  must  bore  four  holes  through  the  surface  of  the  stand  base  at 
particular  points  on  the  edge  of  the  recess  for  the  stand  inlay.  Then  the  screws 
included with the table can be used to fix the table from the underside. 
 
A  user  guide  is  included  with  the  delivery  of  each  angle  table  which  contains  the 
precise  instructions  on  how  to  fit  it.  We  strongly  recommend  that  you  follow  these 
instructions closely, to make sure that you will be able to use the angle table without 
problems. 
 

 

Summary of Contents for OSF 522
























Reviews: