manualshive.com logo in svg

Kerlink 1LOC868-1W868-EU, Installation And Maintenance Manual, Page: 114 / 221

Share
Download
Kerlink 1LOC868-1W868-EU Installation And Maintenance Manual Download Page 114

 

Wirnet iBTS

 

Document title : Installation and 
Maintenance Manual 
Version : 2.0 
Author : SNI 
Date : 04/12/2018 

 

Classification

 

This document is the strict property of Kerlink and shall not be either copied nor sent without express 

written authorization of Kerlink 

Internal Use 

Kerlink m2m technologies reserved rights 

Confidential 

Kerlink – 1 rue Jacqueline Auriol – 35235 THORIGNÉ-FOUILLARD

 

Page 114 / 221

 

Strict confidential 

 

1.8.5.4

 

Indoor Ethernet surge protection 

For the Ethernet link, KERLINK recommends the MJ8-POE-A reference from CITEL. 
This surge protection must be installed indoor, according to its own specifications. 
 
The following picture describes the PoE surge protection: 

 

Figure 76 : MJ8-POE-A Citel 

 

Note:

 the PoE surge protector must be connected to the earth. No cables are provided by 

KERLINK for that purpose. See §1.8.4.2 for additional information. 
 

1.8.5.5

 

Outdoor Ethernet surge protection 

In case the Ethernet surge protection cannot be installed indoor, then KERLINK recommends 
the PD-OUT/SP11 reference from Microsemi. 
This surge protection can be installed indoor, according to its own specifications. 
 
The main characteristics of the PoE surge protection are: 
 

Characteristics 

Specification 

Network 

POE and Gigabit Ethernet, High POE (95W) 

Technology 

Clamping diode 

SPD configuration 

4 pairs + shielded 

Connection to Network 

RJ45 

shielded 

connector 

female 

input/output 

Format 

Metallic box with connectors input/output 

Mounting 

Wall or pole mount 

Operating temperature 

-40°C to +85°C 

Dimensions 

30 x 30 x 190 mm 

Weight 

270g 

Protection rating 

IP66 

Outdoor application 

Yes 

Summary of Contents for 1LOC868-1W868-EU






























































































































































































































Reviews:

No comments