manualshive.com logo in svg

Kerlink 1LOC868-1W868-EU, Installation And Maintenance Manual, Page: 108 / 221

Share
Download
Kerlink 1LOC868-1W868-EU Installation And Maintenance Manual Download Page 108

 

Wirnet iBTS

 

Document title : Installation and 
Maintenance Manual 
Version : 2.0 
Author : SNI 
Date : 04/12/2018 

 

Classification

 

This document is the strict property of Kerlink and shall not be either copied nor sent without express 

written authorization of Kerlink 

Internal Use 

Kerlink m2m technologies reserved rights 

Confidential 

Kerlink – 1 rue Jacqueline Auriol – 35235 THORIGNÉ-FOUILLARD

 

Page 108 / 221

 

Strict confidential 

 

1.8.4.1

 

RJ45 PoE cable 

This cable is not provided with the Wirnet iBTS. 
It neither can be delivered as an accessory. 
 
KERLINK recommends using a PoE cable with the following characteristics: 
 

Characteristics 

Specification 

Category 

6A 

Shielding 

STP (U/FTP) or SSTP (S/FTP)  

Section conductors 

AWG26 or bigger 

External jacket 

LSZH or PUR 

Maximum length 

100 meters 

Operating temperature range 

-20°C to +60°C 

 
KERLINK recommends the following reference: 
TELEGARTNER AMJ 500 U/FTP 4x2x0.55 LSZH Cat. 6A IEC 600332-1 
 
The Ethernet cable must be provided with two RJ45 T 568A (or 568B) plugs on each side: 

 

Figure 67 :RJ45 T-568A plug 

1.8.4.2

 

Earthing cables 

Several  earthing  cables,  wires  or  tapes  are  required  to  connect  the  installation  and  the 
materials to earth for lighting immunity and electrical security. 
The earthing cables are detailed hereafter with recommended wires and sections: 
 

Cable description 

Technical characteristics 

Earthing of the Wirnet iBTS mounting kit 

25mm

2

, copper 

Earthing  of  the  antenna  brackets  (LoRa  antenna, 
GNSS antenna, LTE antenna) 

25mm

2

, copper 

Earthing of the RF coaxial surge protection 

16mm

2

, copper 

Summary of Contents for 1LOC868-1W868-EU






























































































































































































































Reviews:

No comments