Kenwood XD-500 Instruction Manual Download Page 57

Page: 57 / 61

XD-7 5 0 / 7 0 0 / 5 5 0 / 5 0 0 (En)

5 7

ati

tio

lic

ati

tio

cti

In case of difficulty

Remedy

Cause

Symptom

Clean the head referring to “ M aintenance” .

Try another tape.

Play a recorded tape.

Close the holder completely.

Press operations keys in more than a few
seconds after closing the holder.

Press operation keys after w aiting for more
than 4 seconds.

Insert a tape.

Try another tape.

Change the tape transport direction or re-
verse the tape insertion orientation.

Refer to “ Searching for the desired music
program (DPSS)” .

Small time difference does not mean a
malfunction.

Press in stop mode.

Reset the microcomputer.

Clean the head referring to “ M aintenance” .

Try another tape.

Demagnetize the head referring to “ M ain-
tenance” .

Install the system at a distance from other
electric appliances and TV.

Set the Dolby NR to on.

Clean the head referring to “ M aintenance” .

Wind the tape again by fast forw arding,
rew inding or playing from an end to the
other.

Use a cassette w ith an unbroken recording
protect tab or block the hole.

Close the holder completely.

Select the source to be recorded w ith the
input selector key.

Change the tape transport direction of deck
B or reverse the tape insertion orientation.

Fully turn the

M IC M IX.

control knob to the

left.

Sound cannot be produced by pressing
the play key or no operation occurs even
w hen an operation key is pressed.

No operation occurs even w hen an opera-
tion key is pressed.

The DPSS malfunctions.

In dubbing, the tape stops at different
moments in decks A and B.

The cassette holders cannot be opened by
pressing the PUSH OPEN area.

Sound is harsh or high frequencies are not
reproduced.

Sound is distorted.

Noise is noticeable.

Sound vibrates.

Recording cannot be started by pressing
the record key.

Volume of the recorded track changed.

)

The head is dirty.

The tape is w ound too tight due to irregular
w inding.

A nonrecorded tape is played.

The cassette holder is not closed com-
pletely.

The operation key is pressed immediately
after closing the cassette holder.

The operation key is pressed in less than 4
seconds after turning the pow er ON.

A tape is not inserted in the unit.

The tape is w ound too tight due to irregular
w inding.

The tape is fully w ound to one of the reels.

The tape used is not suitable for DPSS, for
example the spaces betw een tunes may be
too short.

This is due to the difference in the tape
length or characteristics of the mechanisms
of tw o cassette decks.

The key is pressed during recording or play-
back.

The microcomputer is malfunctioning due
to external noise.

The head is dirty.

The tape is stretched or shrunk.

The tape being played w as recorded w ith
distorted sound.

The tape head is magnetized.

External noise is induced.

A tape recorded w ith Dolby NR ON is played
w ith Dolby NR OFF.

The capstans or pinch rollers are dirty.

The tape is w ound irregularly.

The recording protect tab of the cassette
has been broken.

The cassette holder is not closed com-
pletely.

The

TAPE

input is selected.

The tape is fully w ound to one of the reels.

M IC M IX.

control knob is moved during

recording.

Cassette deck

A station has been preset but it cannot
be received by pressing the P.CALL key.

Demonstration starts suddenly.

The frequency of the preset station is not
tunable.

The preset memory has been cleared be-
cause the pow er cord has been unplugged
for a long period.

The pow er plug w as unplugged from the
outlet w hile the pow er sw itch w as ON, or
there w as a pow er failure.

Preset stations w ith tunable frequencies.

Preset stations again.

This is not malfunction. Press the

DISP./

DEM O

key to cancel the demontration.

∞
∞

Downloaded from:

http://www.usersmanualguide.com/

Summary of Contents for XD-500






























































Search results

Summary of Contents for XD-500

Reviews:

Related manuals for XD-500

Brands by name

Popular brands

Kenwood XD-500, Instruction Manual

Search results

Summary of Contents for XD-500

Reviews:

Related manuals for XD-500

Brands by name

Popular brands