TK-7108
14
3-2. Connection Procedure
1. Connect the TK-7108 to the personal computer with the
interface cable.
2. When the Power is switched on, user mode can be en-
tered immediately. When the PC sends a command, the
radio enters PC mode.
When data is transmitted from transceiver, the red LED
blink.
When data is received by the transceiver, the green LED
blink.
In the PC mode, 4CH LEDs, [MON] LED and [
●
] LED are
turned on.
Notes :
• The data stored in the personal computer must match
model type when it is written into the EEPROM.
• Attach the interface cable, then change the TK-7108 to PC
mode.
3-3. KPG-46 Description
(PC programming interface cable : Option)
The KPG-46 is required to interface the TK-7108 to the
computer. It has a circuit in its D-subconnector (25-pin) case
that converts the RS-232C logic level to the TTL level.
The KPG-46 connects the modular microphone jack of the
TK-7108 to the computers RS-232C serial port.
3-4. Programming Software Description
The KPG-70D programming disk is supplied in 3-1/2" disk
format. The software on this disk allows a user to program
TK-7108 radio via a programming interface cable (KPG-46).
3-5. Programming With IBM PC
If data is transferred to the transceiver from an IBM PC
with the KPG-70D, the destination data (basic radio informa-
tion) for each set can be modified.
4. Clone Mode
Programming data can be transferred from one radio to
another by connecting them via their modular microphone
jacks. The operation is as follows (the transmit radio is the
master and the receive radio is the slave).
Note :
Clone mode should enabled.
1. Turn the master TK-7108 power ON with the [1] key held
down. The TK-7108 [
●
] LED is turned on.
2. Power on the slave TK-7108.
3. Connect the cloning cable (No. E30-3382-05) to the modu-
lar microphone jacks on the master and slave.
4. Press the [
●
] key on the master TK-7108 transceiver. The
data of the master is sent to the slave. While the master is
sending data, [TX] LED blinked. While the slave is receiv-
ing the data, 4 LEDs, [MON] LED, [
●
] LED are turned on
and [BUSY] LED blinked. When cloning of data is com-
pleted, the master [TX] LED turned off, and the slave auto-
matically operates in the User mode. The slave can then
be operated by the same program as the master.
5. The other slave can be continuously cloned. Carry out the
operation in step 2 to 4.
REALIGNMENT /
!
PJOK=
!
NK
!"#$
qhJTNMU
!"#$
OK
!"#$%&'()*+,-./0123456
!"#$%&'()*+,-.
!"#$%&'()*+,-./
!"#$%&'()*+,-./01
!"#$%
Q
!"#$
=xjlkz=
!
=x
●
z=
!
!"#$%&'()*+,
bbmolj
!"
!"#$%&'
qhJTNMU
!"#$%&'(
PJPK=hmdJQS
======E
!"#$%&'(
F
hmdJQS
qhJTNMU
!"#$%&
a
!
=EOR
F=
!"#$%"&'("&)*+
opJOPO`
!"
qqi
hmdJQS
qhJTNMU
!"#$%&
opJOPO`
!
PJQK=
!"#
hmdJTMa
!"#$
PJNLO
! "#$%&
!"#$
=EhmdJQSF=
qhJTNMU
!"#$
PJRK=
f_j
!"
!"
hmdJTMa
f_j
!"#$%&'(
!"#"$%
=E
!"#$%
F=
!"#
QK=
!
!"#$%&'()*+,-./01+,-./2
!"#$%&'()*+
=E
!"#$%&'()
!"#
F
!"#$
NK
=xNz=
!
qhJTNMU
!
qhJTNMU
=x
●
z=
!"
OK
!
qhJTNMU
!
PK
!"#$
=EkçKbPMJPPUOJMRF=
!"#$%"&
!"#
QK
qhJTNMU
!
= x
●
z=
!"#$%&'()*
!"#$%
=xquz=
!"#$%&'()*+
Q
!"
=xjlkz=
!
=x
●
z=
!"
=x_rpvz=
!"#$%&'()*+
=xquz=
!"#$%&'
!"#$%&'()*+,-./01,23456
RK
!"#$%&'()*+,-
O
Q
!
