Kenwood TK-2170 SERIES Function Reference Download

Page: 53 / 142

14 CONVENTIONAL GROUP

FUNC (K)/Ver. 1.01

Confidential

Contents

Index

14.2 Channel

The following functions relating to Conventional Group
Channels can be configured by using KPG-101D:
•

Receive Frequency

•

Transmit Frequency

•

QT/DQT Decode

•

QT/DQT Encode

•

Channel Name

•

Transmit Power

•

Wide/ Narrow

•

Optional Signaling

•

Busy Channel Lockout

•

PTT ID

•

PTT ID (BOT)

•

PTT ID (EOT)

•

Scan Add

•

Beat Shift

•

Compander

•

Data

•

Voice Scrambler

•

Scrambler Code

14.2.1 Receive Frequency

Receive Frequency can be configured by using
KPG-101D.

Configuration using KPG-101D

•

Configuring the Receive Frequency (Refer to
FPRG 6.4.3 Receive Frequency.)

14.2.2 Transmit Frequency

Transmit Frequency can be configured by using
KPG-101D.

Configuration using KPG-101D

•

Configuring the Transmit Frequency (Refer to
FPRG 6.4.4 Transmit Frequency.)

14.2.3 QT/DQT Decode

QT/DQT is the signaling used for facilitating
communication within a group when sharing the same
channel with several groups (Talk Group).

(Refer to 16.1

QT/DQT Decode/ Encode on page 55.)

QT/DQT Decode can be configured for each channel by
using KPG-101D.

Configuration using KPG-101D

•

Configuring the QT/DQT Decode (Refer to FPRG
6.4.5 QT/DQT Decode.)

14.2.4 QT/DQT Encode

QT/DQT is the signaling used for facilitating
communication within a group when sharing the same
channel with several groups (Talk Group).

(Refer to 16.1

QT/DQT Decode/ Encode on page 55.)

QT/DQT Encode can be configured for each channel by
using KPG-101D.

Configuration using KPG-101D

•

Configuring the QT/DQT Encode (Refer to FPRG
6.4.6 QT/DQT Encode.)

14.2.5 Channel Name

Channel Name can be used to assign a name to a
channel.

(Refer to 3.4.3 Channel Name on page 16.)

Channel Name can be configured by using KPG-101D.

Configuration using KPG-101D

•

Configuring the Channel Name (Refer to FPRG
6.4.7 Channel Name.)

14.2.6 ID

ID is used for DTMF Signaling.
ID can be configured by using KPG-101D. (Refer to
FPRG 6.4.8 ID.)

Summary of Contents for TK-2170 SERIES















































































































































Search results

Summary of Contents for TK-2170 SERIES

Reviews:

Related manuals for TK-2170 SERIES

Brands by name

Popular brands

Kenwood TK-2170 SERIES, Function Reference

Search results

Summary of Contents for TK-2170 SERIES

Reviews:

Related manuals for TK-2170 SERIES

Brands by name

Popular brands