Kenwood TK-2170 SERIES Function Reference Download | Manualshive

Page: 35 / 142

background image

4 SOUNDS

FUNC (K)/Ver. 1.01

Confidential

23

4.6 PTT Proceed Tone

The transceiver emits this tone if communication is
possible after the

PTT

switch is pressed. The transceiver

can be configured to emit the PTT Proceed Tone.
In Trunking System, a user must start talking after the
repeater is allocated when the

PTT

switch is pressed.

However, this duration is not always same, so that it is
difficult for the user to know when to start talking after
pressing the

PTT

switch. With this tone enabled, the user

can smoothly start talking after the Proceed Tone sounds.
The PTT Proceed Tone can be also used while the
transceiver is executing a Conventional Group scan.
The transceiver can be configured to emit the Proceed
Tone by using KPG-101D.

Note:

The audio is not emitted until the transceiver emits the Proceed
Tone sound even if a user starts talking after pressing the

PTT

switch.

If the PTT ID is configured for the channel while sending the
DTMF, 2-tone or Fleetsync code, the PTT Proceed Tone
configuration is reset. In this case, the configuration for PTT ID
Sidetone (FleetSync), Sidetone (DTMF) or Sidetone (2-tone) is
enabled.

Configuration using KPG-101D

•

Configuring the PTT Proceed Tone (Conventional
Group) (Refer to FPRG 6.7.3 Conventional Tab -
PTT Proceed Tone.)

•

Configuring the PTT Proceed Tone (Trunking
System) (Refer to FPRG 6.7.4 Trunking Tab - PTT
Proceed Tone.)

4.7 Proceed Tone Delay Time

This function can be used to control the caller’s speaker
to emit the PTT Proceed Tone after the configured
Proceed Tone Delay Time elapses.
This function prevents the transceiver on the receiving
side from missing the first part of calls.
The Proceed Tone Delay Time can be configured by
using KPG-101D. The Proceed Tone Delay Time for the
caller can be configured in conjunction with the Decode
time of the receiving party.

Note:

The Proceed Tone Delay Time cannot be configured if the
PTT Proceed Tone is disabled.

Configuration using KPG-101D

•

Configuring the Proceed Tone Delay Time
(Conventional Group) (Refer to FPRG 6.7.3
Conventional Tab - Proceed Tone Delay Time.)

•

Configuring the Proceed Tone Delay Time
(Trunking System) (Refer to FPRG 6.7.4 Trunking
Tab - Proceed Tone Delay Time.)

«
...
33
34
35
36
37
...
»

Summary of Contents for TK-2170 SERIES















































































































































Reviews:

No comments

Related manuals for TK-2170 SERIES

AZ9055 - Portable Radio Cass Rec

Brand: Magnavox Pages: 20

Brand: GOWIN Pages: 2

Brand: Eberg Pages: 14

Invertron 4500L-3P-4728

Brand: California Instruments Pages: 6

Brand: Radio Shack Pages: 64

Brand: Hannlomax Pages: 2

Brand: Koshin America Corporation Pages: 12

Brand: Stanford Research Systems Pages: 55

Brand: Sytech Pages: 4

Brand: ZIPPER MASCHINEN Pages: 93

Brand: Grundig Pages: 162

Brand: C. Crane Pages: 32

Brand: Grundig Pages: 36

WEDECO SMOevo PLUS Series

Brand: Xylem Pages: 179

TOWER LIGHT CUBE+ HYBRID

Brand: Generac Power Systems Pages: 74

Brand: TTI Technologies Pages: 14

Brand: LENCO Pages: 31

Brand: Revo Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands