Kenwood ProTalk NX-240V16P, Operating Manual

Page: 3 / 4

CHANNEL CONFIRMATION MODE
To confirm your channel settings:
[1] With the transceiver power OFF, press and hold the PTT switch while
turning the transceiver power ON.
• Continue to hold the PTT switch until the LED lights
orange and the transceiver announces “Confirm” .
[2]
Release the PTT switch.
• Transceiver announces “ Zone 1 Analog (or Digital )”.
[3]
Pressing the Side 1 key or Side 2 key will toggle between “Zone 1”
and “Zone 2” . Select a zone by pressing the PTT switch.
[4]
Rotate the Channel selector to your desired channel.
• Transceiver announces the channel table number, tone number,
scrambler and VOX settings of the selected channel.
[5] Turn the transceiver power OFF and then ON again to return to
normal operation.
Note: The transceiver will automatically return to normal operation if no action is performed for 20 seconds.
VOX GAIN LEVEL SETUP MODE
To change the VOX Gain level:
[1] With the transceiver power OFF, press and hold the Side 1 key
while turning the transceiver power ON.
• Continue to hold the
Side 1 key until the LED lights
orange and the transceiver beeps.
[2]
Release the Side 1 key.
• Transceiver announces the current VOX Gain Level (OFF, 1~10).
OFF : a double beep
1 : the least sensitive
10 : the most sensitive
[3]
Press the Side 1 key: Increment VOX gain level by 1.
(this will adjust the VOX gain level of the radio)
Press the
Side 2 key: Turn VOX ON (a single beep)/OFF (a double beep).
(this will change the ON/OFF setting for the current channel of the current zone)
•
To change channel: Rotate the Channel selector
•
To change zone: Hold the Side 2 key
Press the
PTT switch: Confirm the VOX Gain Level.
[4]
Turn the transceiver power OFF and then ON again to return to normal operation.
Note: The transceiver will automatically return to normal operation if no action is performed for 20 seconds.
“Confirm”
Select a
channel to get
a confirmation
Select by PTT
Change the Zone
A beep
Confirm VOX level
Press:
Change VOX level
Press:
VOX ON/OFF
Hold:
Change Zone
Change channel for VOX
ON/OFF per channel
KEY ASSIGNMENT MODE
This transceiver allows you to reprogram the Side 1 and 2 keys with any of the functions listed in the table below.
Each key can be configured to have two functions by a
Press and a Hold . (some features cannot be assigned as
a Press or a Hold function.
Table
Number
Function Name Descriptions
Side 1 Key Side 2 Key
Press Hold Press Hold
(00) None
No Function
○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○
(01) Calling Alert
Transmits a Calling Alert Tone upon a press of the Calling Alert key.
This function cannot be assigned as a Hold function.
If "Calling Alert" is selected from the Press dropdown list, None will
automatically be configured in the Hold dropdown list, and this
configuration cannot be changed.
○ ○ ○ ○
--
○ ○ ○ ○
--
(02) CW Message
Sends the configured CW Message.
This function can be configured if a message is configured for CW
Message in the CW ID window.
○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○
(03) Key Lock
Toggles the Key Lock between enabled and disabled. While Key
Lock is enabled, key functions will be disabled.
Turning the transceiver OFF and ON again will disable the Key Lock,
and key functions can be used.
Following are keys that are enabled even if the Key Lock is enabled:
•
PTT switch
•
Key Lock
•
Key Lock with Status Memory
•
Super Lock
•
Squelch Off
•
Squelch Off Momentary
•
Monitor
•
Monitor Momentary
•
Selector
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
(04) Key Lock with Status Memory
The Same function as the key lock, however, turning the transceiver
OFF and ON again will NOT disable the Key Lock, and keys remain
locked.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
(05) Monitor
Toggles the Monitor between enabled and disabled. While Monitor
is disabled, the transceiver allows a carrier to open the squelch
regardless of configuration for signaling.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
(06) Monitor Momentary
While this key is pressed and held, the transceiver is disabled from
monitoring the configured signaling and the squelch is opened upon
detection of a carrier.
This function cannot be assigned as a Hold function.
If "Monitor Momentary" is selected from the Press dropdown list,
None will automatically be configured in the Hold dropdown list, and
this configuration cannot be changed.
○
○ ○
○
--
○
○ ○
○
--
(07) Scan
Switches the Scan On or Off.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
(08) Scan Temporary Delete
Temporarily deletes a channel added to the scanning sequence from
the sequence.
If a channel for which Scan Add is enabled is selected and if a Scan
Temporary Delete key is pressed while scan pauses, the channel will
be deleted from the scanning sequence.
Status of channel deleted from the scanning sequence by this
function cannot be retained in the transceiver. Reactivating the scan
by pressing the Scan key returns the transceiver to the original state.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○