background image

20

   

|

   

KDC-MP5043U/ KDC-MP543U/ KDC-MP443U

Troubleshooting Guide

Some functions of this unit may be disabled by 
some settings made on this unit. 

 ! 

  •  Cannot set up the subwoofer.

 

•  Cannot set up the low pass filter.

 

•  No output from the subwoofer.

 •  <Subwoofer output> of <Basic Operation> (page 4) 

is not set to On. 

 

•  Preout is not set to subwoofer. 

 “SWPRE”  of 

<Menu system> (page 6) 

 ! 

  •  Cannot register a security code.

 

•  Cannot set up Display.

 <Demonstration mode setting> (page 11) is not 

turned off. 

What might seem to be a malfunction in your unit 
may just be the result of slight misoperation or 
miswiring. Before calling service, first check the 
following table for possible problems.

General

 ? 

  The Touch Sensor Tone does not sound.

  The preout jack is being used.

  The Touch Sensor Tone cannot be output from 

the preout jack.

Tuner source

 ? 

  Radio reception is poor.

  The car antenna is not extended.

  Pull the antenna out all the way.

Disc source

 ? 

  The specified disc does not play, but another one 

plays instead.

  The specified CD is quite dirty.

  Clean the CD, referring to the CD cleaning of the 

section on <Handling CDs> (page 3).

  The disc is loaded in a different slot from that 

specified.

  Eject the disc magazine and check the number 

for the specified disc.

  The disc is severely scratched.

  Try another disc instead.

Audio file source

 ? 

  The sound skips when an Audio file is being 

played.

  The media is scratched or dirty.

☞ 

Clean the media, referring to the CD cleaning of 
the section on <Handling CDs> (page 3).

  The recording condition is bad.

  Record the media again or use another media.

B64-4439-00̲00̲M̲English.indd   20

B64-4439-00̲00̲M̲English.indd   20

08.9.24   1:53:13 PM

08.9.24   1:53:13 PM

Summary of Contents for KDC-MP443U























Reviews: